I tried both with Arduino Uno and Nano Every and I get the sane error. I’ve tested MCCI LoRaWAN LMIC, too. Beside the oslmic.c:53 error in the serial monitor, I get a pinmap error in the compiler. Wiring is ok, so I guess I have to accept that it’s a soldering problem, due to my terrible soldering skills. I’ll post some pics of that.
Your Gnd joint looks like it could be a dry joint.
I’d touch each of them up looking to remove the excess solder and make sure it flows like a liquid. The soldering iron tip can not transfer any heat by itself, there must be a small amount of solder on it to do that for you. But not so much that you can start sculpting with it.
I think you’ll see it’s a warning about you having to define the pin map, not an error.
I’d stick with the Nano Every - far more room for both program and variables.
You don’t need to test MCCI LMIC, it definitely works (I was coding on it most of the weekend), you just have to tell it which pins are being used for NSS, DIO0 and DIO1. Once you’ve got that going, you can focus on the EUI’s & AppKey.
With the appropriate 5V to 3.3V Logic level conversion circuits I presume.
That device does not look like any of the Hope RFM95s I have seen. Hope normally have a different marking on the RF chip they use RF95.
I would alse be very cautious wiring LoRa modules up like that, if the antenna wire becomes disconnected when you attempt to transmit it could let the devices magic smoke out.
1 Like
Thank you. I’ll proceed with the soldering tips you gave me, trying to fix it. And then try again with LMIC. I’ll update you. (By the way, I’m using a “single channel” Raspberry Pi 4 Lora Gateway, I saw in the forum that it’s not a good idea)
Eeeehm, nope. I am not using a logic level converter… I saw video on youtube of people not using it… By the way, I also have a Hope LoRa module, but I think I’ve damaged it.
So not only, zapping 3.3V module with 5V and solder bridges but also …
We don’t say it’s not a good idea, we say they should not be used due to the disruption to the network. And you have to alter LMIC to be able to cope with a SPCF which isn’t trivial.
Please disconnect immediately and read: Single Channel Packet Forwarders (SCPF) are obsolete and not supported
If you want to make some progress, get a TTIG for a gateway and buy a board supported by LMIC-node. I’d normally recommend the Adafruit Feather M0 with RFM95 but in this instance, as it requires some delicate soldering, maybe best to pick something else. 
Thanks for your rapid answer and kind suggestions! Do you think I still can make it with Arduino Nano Every, 3.3 to 5 V logic level converter and a Hope module?
I’ve a test device with a Nano Every and I have my own PCB with an ATmega4808 + RFM95 on it, it works fine with LMIC once you know LMIC.
You may want to use a breadboard & jumper cables until you’ve refined your soldering technique.
You still need a proper gateway.
I have the same problem with Dragino Lora Shield + Arduino Uno.
When I use your program, I get only this.
I am not told weather the lora device is found or not.
Any advice for me?
There are no writes to the LoRa device, something strange there.
Look at the code, It has to print found or not found;
if (begin(NSS))
{
Serial.println(F("LoRa Device found"));
}
else
{
Serial.println(F("No device responding"));
}
Which TTN library have you tried ?
An additional comment: Some of the registers are not what the should be, so it looks like there are read problems over the SPI bus.
As per the program notes the startup should be:
2_Register_Test Starting
LoRa Device found
Device version 0x12
Frequency at Start 434000000
Registers at Start
Reg 0 1 2 3 4 5 6 7 8 9 A B C D E F
0x00 00 09 1A 0B 00 52 6C 80 00 4F 09 2B 20 08 02 0A
etc.
1 Like
Thanks for the reply, I think I purchased a faulty dragino lora shield. Even the light on the shield was not turning one, once it was connected to power.
I think it was a faulty one.
Good morning,
I am using an Arduino Mega 2560 board with a LoRa Shield RFM95W radio module. However I use LMIC to send my data to a Dragino LPS8N gateway.
And when I upload my program to the Arduino board nothing happens and I get the error displayed on the serial monitor:
Arduino\libraries\LMIC-Arduino\src\lmic\radio.c:689
Here is the picture of the shield 
Help me please.
Here is my test code on arduino:
const int Pintest =13;
//---------------------------------------------------
#include <lmic.h>
#include <hal/hal.h>
#include <SPI.h>
// LoRaWAN NwkSKey, network session key
// This is the default Semtech key, which is used by the early prototype TTN
// network.
static const PROGMEM u1_t NWKSKEY[16] = { 0x91, 0xA4, 0xAE, 0x05, 0x61, 0x89, 0x16, 0xCF, 0x09, 0x73, 0x51, 0x70, 0x19, 0xD1, 0xC3, 0xE2 };
// LoRaWAN AppSKey, application session key
// This is the default Semtech key, which is used by the early prototype TTN
// network.
static const u1_t PROGMEM APPSKEY[16] = { 0x79, 0xDB, 0xD8, 0xE4, 0x98, 0xF8, 0x19, 0xE1, 0xA6, 0x52, 0x5D, 0x4F, 0x79, 0x43, 0x71, 0x5D };
// LoRaWAN end-device address (DevAddr)
static const u4_t DEVADDR = 0x010C2D70; // ← Change this address for every node!
// These callbacks are only used in over-the-air activation, so they are
// left empty here (we cannot leave them out completely unless
// DISABLE_JOIN is set in config.h, otherwise the linker will complain).
void os_getArtEui (u1_t* buf) { }
void os_getDevEui (u1_t* buf) { }
void os_getDevKey (u1_t* buf) { }
static uint8_t mydata = “Hello, world!”;
static osjob_t sendjob;
// Schedule TX every this many seconds (might become longer due to duty
// cycle limitations).
const unsigned TX_INTERVAL = 10;
// Pin mapping
const lmic_pinmap lmic_pins = {
.nss = 10,
.rxtx = LMIC_UNUSED_PIN,
.rst = 9,
.dio = {2, 6, 7},
};
void onEvent (ev_t ev) {
Serial.print(os_getTime());
Serial.print(": ");
switch(ev) {
case EV_SCAN_TIMEOUT:
Serial.println(F(“EV_SCAN_TIMEOUT”));
break;
case EV_BEACON_FOUND:
Serial.println(F(“EV_BEACON_FOUND”));
break;
case EV_BEACON_MISSED:
Serial.println(F(“EV_BEACON_MISSED”));
break;
case EV_BEACON_TRACKED:
Serial.println(F(“EV_BEACON_TRACKED”));
break;
case EV_JOINING:
Serial.println(F(“EV_JOINING”));
break;
case EV_JOINED:
Serial.println(F(“EV_JOINED”));
break;
case EV_RFU1:
Serial.println(F(“EV_RFU1”));
break;
case EV_JOIN_FAILED:
Serial.println(F(“EV_JOIN_FAILED”));
break;
case EV_REJOIN_FAILED:
Serial.println(F(“EV_REJOIN_FAILED”));
break;
case EV_TXCOMPLETE:
Serial.println(F(“EV_TXCOMPLETE (includes waiting for RX windows)”));
if (LMIC.txrxFlags & TXRX_ACK)
Serial.println(F(“Received ack”));
if (LMIC.dataLen) {
Serial.println(F(“Received “));
Serial.println(LMIC.dataLen);
Serial.println(F(” bytes of payload”));
}
// Schedule next transmission
os_setTimedCallback(&sendjob, os_getTime()+sec2osticks(TX_INTERVAL), do_send);
break;
case EV_LOST_TSYNC:
Serial.println(F(“EV_LOST_TSYNC”));
break;
case EV_RESET:
Serial.println(F(“EV_RESET”));
break;
case EV_RXCOMPLETE:
// data received in ping slot
Serial.println(F(“EV_RXCOMPLETE”));
break;
case EV_LINK_DEAD:
Serial.println(F(“EV_LINK_DEAD”));
break;
case EV_LINK_ALIVE:
Serial.println(F(“EV_LINK_ALIVE”));
break;
default:
Serial.println(F(“Unknown event”));
break;
}
}
void do_send(osjob_t* j){
// Check if there is not a current TX/RX job running
if (LMIC.opmode & OP_TXRXPEND) {
Serial.println(F(“OP_TXRXPEND, not sending”));
} else {
uint8_t buff[3];
buff[0] = 1;
LMIC_setTxData2(1, buff, sizeof(buff), 0);
Serial.println(F("Packet queued"));
}
// Next TX is scheduled after TX_COMPLETE event.
}
void setup() {
Serial.begin(115200);
#ifdef VCC_ENABLE
// For Pinoccio Scout boards
pinMode(VCC_ENABLE, OUTPUT);
digitalWrite(VCC_ENABLE, HIGH);
delay(1000);
#endif
//----------------------------------------------------
pinMode(Pintest, OUTPUT);
// LMIC init
os_init();
// Reset the MAC state. Session and pending data transfers will be discarded.
LMIC_reset();
LMIC_setClockError(MAX_CLOCK_ERROR * 10 / 100);
// Set static session parameters. Instead of dynamically establishing a session
// by joining the network, precomputed session parameters are be provided.
#ifdef PROGMEM
// On AVR, these values are stored in flash and only copied to RAM
// once. Copy them to a temporary buffer here, LMIC_setSession will
// copy them into a buffer of its own again.
uint8_t appskey[sizeof(APPSKEY)];
uint8_t nwkskey[sizeof(NWKSKEY)];
memcpy_P(appskey, APPSKEY, sizeof(APPSKEY));
memcpy_P(nwkskey, NWKSKEY, sizeof(NWKSKEY));
LMIC_setSession (0x1, DEVADDR, nwkskey, appskey);
#else
// If not running an AVR with PROGMEM, just use the arrays directly
LMIC_setSession (0x1, DEVADDR, NWKSKEY, APPSKEY);
#endif
#if defined(CFG_eu868)
// Set up the channels used by the Things Network, which corresponds
// to the defaults of most gateways. Without this, only three base
// channels from the LoRaWAN specification are used, which certainly
// works, so it is good for debugging, but can overload those
// frequencies, so be sure to configure the full frequency range of
// your network here (unless your network autoconfigures them).
// Setting up channels should happen after LMIC_setSession, as that
// configures the minimal channel set.
// NA-US channels 0-71 are configured automatically
LMIC_setupChannel(0, 868100000, DR_RANGE_MAP(DR_SF12, DR_SF7), BAND_CENTI); // g-band
LMIC_setupChannel(1, 868300000, DR_RANGE_MAP(DR_SF12, DR_SF7B), BAND_CENTI); // g-band
LMIC_setupChannel(2, 868500000, DR_RANGE_MAP(DR_SF12, DR_SF7), BAND_CENTI); // g-band
LMIC_setupChannel(3, 867100000, DR_RANGE_MAP(DR_SF12, DR_SF7), BAND_CENTI); // g-band
LMIC_setupChannel(4, 867300000, DR_RANGE_MAP(DR_SF12, DR_SF7), BAND_CENTI); // g-band
LMIC_setupChannel(5, 867500000, DR_RANGE_MAP(DR_SF12, DR_SF7), BAND_CENTI); // g-band
LMIC_setupChannel(6, 867700000, DR_RANGE_MAP(DR_SF12, DR_SF7), BAND_CENTI); // g-band
LMIC_setupChannel(7, 867900000, DR_RANGE_MAP(DR_SF12, DR_SF7), BAND_CENTI); // g-band
LMIC_setupChannel(8, 868800000, DR_RANGE_MAP(DR_FSK, DR_FSK), BAND_MILLI); // g2-band
// TTN defines an additional channel at 869.525Mhz using SF9 for class B
// devices' ping slots. LMIC does not have an easy way to define set this
// frequency and support for class B is spotty and untested, so this
// frequency is not configured here.
#elif defined(CFG_us915)
// NA-US channels 0-71 are configured automatically
// but only one group of 8 should (a subband) should be active
// TTN recommends the second sub band, 1 in a zero based count.
// https://github.com/TheThingsNetwork/gateway-conf/blob/master/US-global_conf.json
LMIC_selectSubBand(1);
#endif
// Disable link check validation
LMIC_setLinkCheckMode(0);
// TTN uses SF9 for its RX2 window.
LMIC.dn2Dr = DR_SF9;
// Set data rate and transmit power for uplink (note: txpow seems to be ignored by the library)
LMIC_setDrTxpow(DR_SF7,14);
// Start job
do_send(&sendjob);
}
//----------------------------------------------------------------------
void loop() {
// put your main code here, to run repeatedly:
os_runloop_once();
digitalWrite(Pintest,HIGH);
delay(1000);
digitalWrite(Pintest,LOW);
delay(1000);
}
//------------------------------------------------------------------
What does it say on this line of the code?
Sorry, my screen reader can’t cope with images and neither can the forum. Please post text as text formatted using the </> tool. But don’t worry, I already know what’s on that line, I was wondering if you did.
But as, like others before you, I don’t see any thoughts on what it might mean.
Ok I will put the code using the </> tool. No I don’t know what exactly I’m a beginner on LMIC.
Do you have a solution for this problem
type or paste code here
/*******************************************************************************
* Copyright (c) 2014-2015 IBM Corporation.
* All rights reserved. This program and the accompanying materials
* are made available under the terms of the Eclipse Public License v1.0
* which accompanies this distribution, and is available at
* http://www.eclipse.org/legal/epl-v10.html
*
* Contributors:
* IBM Zurich Research Lab - initial API, implementation and documentation
*******************************************************************************/
#include "lmic.h"
// ----------------------------------------
// Registers Mapping
#define RegFifo 0x00 // common
#define RegOpMode 0x01 // common
#define FSKRegBitrateMsb 0x02
#define FSKRegBitrateLsb 0x03
#define FSKRegFdevMsb 0x04
#define FSKRegFdevLsb 0x05
#define RegFrfMsb 0x06 // common
#define RegFrfMid 0x07 // common
#define RegFrfLsb 0x08 // common
#define RegPaConfig 0x09 // common
#define RegPaRamp 0x0A // common
#define RegOcp 0x0B // common
#define RegLna 0x0C // common
#define FSKRegRxConfig 0x0D
#define LORARegFifoAddrPtr 0x0D
#define FSKRegRssiConfig 0x0E
#define LORARegFifoTxBaseAddr 0x0E
#define FSKRegRssiCollision 0x0F
#define LORARegFifoRxBaseAddr 0x0F
#define FSKRegRssiThresh 0x10
#define LORARegFifoRxCurrentAddr 0x10
#define FSKRegRssiValue 0x11
#define LORARegIrqFlagsMask 0x11
#define FSKRegRxBw 0x12
#define LORARegIrqFlags 0x12
#define FSKRegAfcBw 0x13
#define LORARegRxNbBytes 0x13
#define FSKRegOokPeak 0x14
#define LORARegRxHeaderCntValueMsb 0x14
#define FSKRegOokFix 0x15
#define LORARegRxHeaderCntValueLsb 0x15
#define FSKRegOokAvg 0x16
#define LORARegRxPacketCntValueMsb 0x16
#define LORARegRxpacketCntValueLsb 0x17
#define LORARegModemStat 0x18
#define LORARegPktSnrValue 0x19
#define FSKRegAfcFei 0x1A
#define LORARegPktRssiValue 0x1A
#define FSKRegAfcMsb 0x1B
#define LORARegRssiValue 0x1B
#define FSKRegAfcLsb 0x1C
#define LORARegHopChannel 0x1C
#define FSKRegFeiMsb 0x1D
#define LORARegModemConfig1 0x1D
#define FSKRegFeiLsb 0x1E
#define LORARegModemConfig2 0x1E
#define FSKRegPreambleDetect 0x1F
#define LORARegSymbTimeoutLsb 0x1F
#define FSKRegRxTimeout1 0x20
#define LORARegPreambleMsb 0x20
#define FSKRegRxTimeout2 0x21
#define LORARegPreambleLsb 0x21
#define FSKRegRxTimeout3 0x22
#define LORARegPayloadLength 0x22
#define FSKRegRxDelay 0x23
#define LORARegPayloadMaxLength 0x23
#define FSKRegOsc 0x24
#define LORARegHopPeriod 0x24
#define FSKRegPreambleMsb 0x25
#define LORARegFifoRxByteAddr 0x25
#define LORARegModemConfig3 0x26
#define FSKRegPreambleLsb 0x26
#define FSKRegSyncConfig 0x27
#define LORARegFeiMsb 0x28
#define FSKRegSyncValue1 0x28
#define LORAFeiMib 0x29
#define FSKRegSyncValue2 0x29
#define LORARegFeiLsb 0x2A
#define FSKRegSyncValue3 0x2A
#define FSKRegSyncValue4 0x2B
#define LORARegRssiWideband 0x2C
#define FSKRegSyncValue5 0x2C
#define FSKRegSyncValue6 0x2D
#define FSKRegSyncValue7 0x2E
#define FSKRegSyncValue8 0x2F
#define FSKRegPacketConfig1 0x30
#define FSKRegPacketConfig2 0x31
#define LORARegDetectOptimize 0x31
#define FSKRegPayloadLength 0x32
#define FSKRegNodeAdrs 0x33
#define LORARegInvertIQ 0x33
#define FSKRegBroadcastAdrs 0x34
#define FSKRegFifoThresh 0x35
#define FSKRegSeqConfig1 0x36
#define FSKRegSeqConfig2 0x37
#define LORARegDetectionThreshold 0x37
#define FSKRegTimerResol 0x38
#define FSKRegTimer1Coef 0x39
#define LORARegSyncWord 0x39
#define FSKRegTimer2Coef 0x3A
#define FSKRegImageCal 0x3B
#define FSKRegTemp 0x3C
#define FSKRegLowBat 0x3D
#define FSKRegIrqFlags1 0x3E
#define FSKRegIrqFlags2 0x3F
#define RegDioMapping1 0x40 // common
#define RegDioMapping2 0x41 // common
#define RegVersion 0x42 // common
// #define RegAgcRef 0x43 // common
// #define RegAgcThresh1 0x44 // common
// #define RegAgcThresh2 0x45 // common
// #define RegAgcThresh3 0x46 // common
// #define RegPllHop 0x4B // common
// #define RegTcxo 0x58 // common
#define RegPaDac 0x5A // common
// #define RegPll 0x5C // common
// #define RegPllLowPn 0x5E // common
// #define RegFormerTemp 0x6C // common
// #define RegBitRateFrac 0x70 // common
// ----------------------------------------
// spread factors and mode for RegModemConfig2
#define SX1272_MC2_FSK 0x00
#define SX1272_MC2_SF7 0x70
#define SX1272_MC2_SF8 0x80
#define SX1272_MC2_SF9 0x90
#define SX1272_MC2_SF10 0xA0
#define SX1272_MC2_SF11 0xB0
#define SX1272_MC2_SF12 0xC0
// bandwidth for RegModemConfig1
#define SX1272_MC1_BW_125 0x00
#define SX1272_MC1_BW_250 0x40
#define SX1272_MC1_BW_500 0x80
// coding rate for RegModemConfig1
#define SX1272_MC1_CR_4_5 0x08
#define SX1272_MC1_CR_4_6 0x10
#define SX1272_MC1_CR_4_7 0x18
#define SX1272_MC1_CR_4_8 0x20
#define SX1272_MC1_IMPLICIT_HEADER_MODE_ON 0x04 // required for receive
#define SX1272_MC1_RX_PAYLOAD_CRCON 0x02
#define SX1272_MC1_LOW_DATA_RATE_OPTIMIZE 0x01 // mandated for SF11 and SF12
// transmit power configuration for RegPaConfig
#define SX1272_PAC_PA_SELECT_PA_BOOST 0x80
#define SX1272_PAC_PA_SELECT_RFIO_PIN 0x00
// sx1276 RegModemConfig1
#define SX1276_MC1_BW_125 0x70
#define SX1276_MC1_BW_250 0x80
#define SX1276_MC1_BW_500 0x90
#define SX1276_MC1_CR_4_5 0x02
#define SX1276_MC1_CR_4_6 0x04
#define SX1276_MC1_CR_4_7 0x06
#define SX1276_MC1_CR_4_8 0x08
#define SX1276_MC1_IMPLICIT_HEADER_MODE_ON 0x01
// sx1276 RegModemConfig2
#define SX1276_MC2_RX_PAYLOAD_CRCON 0x04
// sx1276 RegModemConfig3
#define SX1276_MC3_LOW_DATA_RATE_OPTIMIZE 0x08
#define SX1276_MC3_AGCAUTO 0x04
// preamble for lora networks (nibbles swapped)
#define LORA_MAC_PREAMBLE 0x34
#define RXLORA_RXMODE_RSSI_REG_MODEM_CONFIG1 0x0A
#ifdef CFG_sx1276_radio
#define RXLORA_RXMODE_RSSI_REG_MODEM_CONFIG2 0x70
#elif CFG_sx1272_radio
#define RXLORA_RXMODE_RSSI_REG_MODEM_CONFIG2 0x74
#endif
// ----------------------------------------
// Constants for radio registers
#define OPMODE_LORA 0x80
#define OPMODE_MASK 0x07
#define OPMODE_SLEEP 0x00
#define OPMODE_STANDBY 0x01
#define OPMODE_FSTX 0x02
#define OPMODE_TX 0x03
#define OPMODE_FSRX 0x04
#define OPMODE_RX 0x05
#define OPMODE_RX_SINGLE 0x06
#define OPMODE_CAD 0x07
// ----------------------------------------
// Bits masking the corresponding IRQs from the radio
#define IRQ_LORA_RXTOUT_MASK 0x80
#define IRQ_LORA_RXDONE_MASK 0x40
#define IRQ_LORA_CRCERR_MASK 0x20
#define IRQ_LORA_HEADER_MASK 0x10
#define IRQ_LORA_TXDONE_MASK 0x08
#define IRQ_LORA_CDDONE_MASK 0x04
#define IRQ_LORA_FHSSCH_MASK 0x02
#define IRQ_LORA_CDDETD_MASK 0x01
#define IRQ_FSK1_MODEREADY_MASK 0x80
#define IRQ_FSK1_RXREADY_MASK 0x40
#define IRQ_FSK1_TXREADY_MASK 0x20
#define IRQ_FSK1_PLLLOCK_MASK 0x10
#define IRQ_FSK1_RSSI_MASK 0x08
#define IRQ_FSK1_TIMEOUT_MASK 0x04
#define IRQ_FSK1_PREAMBLEDETECT_MASK 0x02
#define IRQ_FSK1_SYNCADDRESSMATCH_MASK 0x01
#define IRQ_FSK2_FIFOFULL_MASK 0x80
#define IRQ_FSK2_FIFOEMPTY_MASK 0x40
#define IRQ_FSK2_FIFOLEVEL_MASK 0x20
#define IRQ_FSK2_FIFOOVERRUN_MASK 0x10
#define IRQ_FSK2_PACKETSENT_MASK 0x08
#define IRQ_FSK2_PAYLOADREADY_MASK 0x04
#define IRQ_FSK2_CRCOK_MASK 0x02
#define IRQ_FSK2_LOWBAT_MASK 0x01
// ----------------------------------------
// DIO function mappings D0D1D2D3
#define MAP_DIO0_LORA_RXDONE 0x00 // 00------
#define MAP_DIO0_LORA_TXDONE 0x40 // 01------
#define MAP_DIO1_LORA_RXTOUT 0x00 // --00----
#define MAP_DIO1_LORA_NOP 0x30 // --11----
#define MAP_DIO2_LORA_NOP 0xC0 // ----11--
#define MAP_DIO0_FSK_READY 0x00 // 00------ (packet sent / payload ready)
#define MAP_DIO1_FSK_NOP 0x30 // --11----
#define MAP_DIO2_FSK_TXNOP 0x04 // ----01--
#define MAP_DIO2_FSK_TIMEOUT 0x08 // ----10--
// FSK IMAGECAL defines
#define RF_IMAGECAL_AUTOIMAGECAL_MASK 0x7F
#define RF_IMAGECAL_AUTOIMAGECAL_ON 0x80
#define RF_IMAGECAL_AUTOIMAGECAL_OFF 0x00 // Default
#define RF_IMAGECAL_IMAGECAL_MASK 0xBF
#define RF_IMAGECAL_IMAGECAL_START 0x40
#define RF_IMAGECAL_IMAGECAL_RUNNING 0x20
#define RF_IMAGECAL_IMAGECAL_DONE 0x00 // Default
// RADIO STATE
// (initialized by radio_init(), used by radio_rand1())
static u1_t randbuf[16];
#ifdef CFG_sx1276_radio
#define LNA_RX_GAIN (0x20|0x1)
#elif CFG_sx1272_radio
#define LNA_RX_GAIN (0x20|0x03)
#else
#error Missing CFG_sx1272_radio/CFG_sx1276_radio
#endif
static void writeReg (u1_t addr, u1_t data ) {
hal_pin_nss(0);
hal_spi(addr | 0x80);
hal_spi(data);
hal_pin_nss(1);
}
static u1_t readReg (u1_t addr) {
hal_pin_nss(0);
hal_spi(addr & 0x7F);
u1_t val = hal_spi(0x00);
hal_pin_nss(1);
return val;
}
static void writeBuf (u1_t addr, xref2u1_t buf, u1_t len) {
hal_pin_nss(0);
hal_spi(addr | 0x80);
for (u1_t i=0; i<len; i++) {
hal_spi(buf[i]);
}
hal_pin_nss(1);
}
static void readBuf (u1_t addr, xref2u1_t buf, u1_t len) {
hal_pin_nss(0);
hal_spi(addr & 0x7F);
for (u1_t i=0; i<len; i++) {
buf[i] = hal_spi(0x00);
}
hal_pin_nss(1);
}
static void opmode (u1_t mode) {
writeReg(RegOpMode, (readReg(RegOpMode) & ~OPMODE_MASK) | mode);
}
static void opmodeLora() {
u1_t u = OPMODE_LORA;
#ifdef CFG_sx1276_radio
u |= 0x8; // TBD: sx1276 high freq
#endif
writeReg(RegOpMode, u);
}
static void opmodeFSK() {
u1_t u = 0;
#ifdef CFG_sx1276_radio
u |= 0x8; // TBD: sx1276 high freq
#endif
writeReg(RegOpMode, u);
}
// configure LoRa modem (cfg1, cfg2)
static void configLoraModem () {
sf_t sf = getSf(LMIC.rps);
#ifdef CFG_sx1276_radio
u1_t mc1 = 0, mc2 = 0, mc3 = 0;
switch (getBw(LMIC.rps)) {
case BW125: mc1 |= SX1276_MC1_BW_125; break;
case BW250: mc1 |= SX1276_MC1_BW_250; break;
case BW500: mc1 |= SX1276_MC1_BW_500; break;
default:
ASSERT(0);
}
switch( getCr(LMIC.rps) ) {
case CR_4_5: mc1 |= SX1276_MC1_CR_4_5; break;
case CR_4_6: mc1 |= SX1276_MC1_CR_4_6; break;
case CR_4_7: mc1 |= SX1276_MC1_CR_4_7; break;
case CR_4_8: mc1 |= SX1276_MC1_CR_4_8; break;
default:
ASSERT(0);
}
if (getIh(LMIC.rps)) {
mc1 |= SX1276_MC1_IMPLICIT_HEADER_MODE_ON;
writeReg(LORARegPayloadLength, getIh(LMIC.rps)); // required length
}
// set ModemConfig1
writeReg(LORARegModemConfig1, mc1);
mc2 = (SX1272_MC2_SF7 + ((sf-1)<<4));
if (getNocrc(LMIC.rps) == 0) {
mc2 |= SX1276_MC2_RX_PAYLOAD_CRCON;
}
writeReg(LORARegModemConfig2, mc2);
mc3 = SX1276_MC3_AGCAUTO;
if ((sf == SF11 || sf == SF12) && getBw(LMIC.rps) == BW125) {
mc3 |= SX1276_MC3_LOW_DATA_RATE_OPTIMIZE;
}
writeReg(LORARegModemConfig3, mc3);
#elif CFG_sx1272_radio
u1_t mc1 = (getBw(LMIC.rps)<<6);
switch( getCr(LMIC.rps) ) {
case CR_4_5: mc1 |= SX1272_MC1_CR_4_5; break;
case CR_4_6: mc1 |= SX1272_MC1_CR_4_6; break;
case CR_4_7: mc1 |= SX1272_MC1_CR_4_7; break;
case CR_4_8: mc1 |= SX1272_MC1_CR_4_8; break;
}
if ((sf == SF11 || sf == SF12) && getBw(LMIC.rps) == BW125) {
mc1 |= SX1272_MC1_LOW_DATA_RATE_OPTIMIZE;
}
if (getNocrc(LMIC.rps) == 0) {
mc1 |= SX1272_MC1_RX_PAYLOAD_CRCON;
}
if (getIh(LMIC.rps)) {
mc1 |= SX1272_MC1_IMPLICIT_HEADER_MODE_ON;
writeReg(LORARegPayloadLength, getIh(LMIC.rps)); // required length
}
// set ModemConfig1
writeReg(LORARegModemConfig1, mc1);
// set ModemConfig2 (sf, AgcAutoOn=1 SymbTimeoutHi=00)
writeReg(LORARegModemConfig2, (SX1272_MC2_SF7 + ((sf-1)<<4)) | 0x04);
#else
#error Missing CFG_sx1272_radio/CFG_sx1276_radio
#endif /* CFG_sx1272_radio */
}
static void configChannel () {
// set frequency: FQ = (FRF * 32 Mhz) / (2 ^ 19)
uint64_t frf = ((uint64_t)LMIC.freq << 19) / 32000000;
writeReg(RegFrfMsb, (u1_t)(frf>>16));
writeReg(RegFrfMid, (u1_t)(frf>> 8));
writeReg(RegFrfLsb, (u1_t)(frf>> 0));
}
static void configPower () {
#ifdef CFG_sx1276_radio
// no boost used for now
s1_t pw = (s1_t)LMIC.txpow;
if(pw >= 17) {
pw = 15;
} else if(pw < 2) {
pw = 2;
}
// check board type for BOOST pin
writeReg(RegPaConfig, (u1_t)(0x80|(pw&0xf)));
writeReg(RegPaDac, readReg(RegPaDac)|0x4);
#elif CFG_sx1272_radio
// set PA config (2-17 dBm using PA_BOOST)
s1_t pw = (s1_t)LMIC.txpow;
if(pw > 17) {
pw = 17;
} else if(pw < 2) {
pw = 2;
}
writeReg(RegPaConfig, (u1_t)(0x80|(pw-2)));
#else
#error Missing CFG_sx1272_radio/CFG_sx1276_radio
#endif /* CFG_sx1272_radio */
}
static void txfsk () {
// select FSK modem (from sleep mode)
writeReg(RegOpMode, 0x10); // FSK, BT=0.5
ASSERT(readReg(RegOpMode) == 0x10);
// enter standby mode (required for FIFO loading))
opmode(OPMODE_STANDBY);
// set bitrate
writeReg(FSKRegBitrateMsb, 0x02); // 50kbps
writeReg(FSKRegBitrateLsb, 0x80);
// set frequency deviation
writeReg(FSKRegFdevMsb, 0x01); // +/- 25kHz
writeReg(FSKRegFdevLsb, 0x99);
// frame and packet handler settings
writeReg(FSKRegPreambleMsb, 0x00);
writeReg(FSKRegPreambleLsb, 0x05);
writeReg(FSKRegSyncConfig, 0x12);
writeReg(FSKRegPacketConfig1, 0xD0);
writeReg(FSKRegPacketConfig2, 0x40);
writeReg(FSKRegSyncValue1, 0xC1);
writeReg(FSKRegSyncValue2, 0x94);
writeReg(FSKRegSyncValue3, 0xC1);
// configure frequency
configChannel();
// configure output power
configPower();
// set the IRQ mapping DIO0=PacketSent DIO1=NOP DIO2=NOP
writeReg(RegDioMapping1, MAP_DIO0_FSK_READY|MAP_DIO1_FSK_NOP|MAP_DIO2_FSK_TXNOP);
// initialize the payload size and address pointers
writeReg(FSKRegPayloadLength, LMIC.dataLen+1); // (insert length byte into payload))
// download length byte and buffer to the radio FIFO
writeReg(RegFifo, LMIC.dataLen);
writeBuf(RegFifo, LMIC.frame, LMIC.dataLen);
// enable antenna switch for TX
hal_pin_rxtx(1);
// now we actually start the transmission
opmode(OPMODE_TX);
}
static void txlora () {
// select LoRa modem (from sleep mode)
//writeReg(RegOpMode, OPMODE_LORA);
opmodeLora();
ASSERT((readReg(RegOpMode) & OPMODE_LORA) != 0);
// enter standby mode (required for FIFO loading))
opmode(OPMODE_STANDBY);
// configure LoRa modem (cfg1, cfg2)
configLoraModem();
// configure frequency
configChannel();
// configure output power
writeReg(RegPaRamp, (readReg(RegPaRamp) & 0xF0) | 0x08); // set PA ramp-up time 50 uSec
configPower();
// set sync word
writeReg(LORARegSyncWord, LORA_MAC_PREAMBLE);
// set the IRQ mapping DIO0=TxDone DIO1=NOP DIO2=NOP
writeReg(RegDioMapping1, MAP_DIO0_LORA_TXDONE|MAP_DIO1_LORA_NOP|MAP_DIO2_LORA_NOP);
// clear all radio IRQ flags
writeReg(LORARegIrqFlags, 0xFF);
// mask all IRQs but TxDone
writeReg(LORARegIrqFlagsMask, ~IRQ_LORA_TXDONE_MASK);
// initialize the payload size and address pointers
writeReg(LORARegFifoTxBaseAddr, 0x00);
writeReg(LORARegFifoAddrPtr, 0x00);
writeReg(LORARegPayloadLength, LMIC.dataLen);
// download buffer to the radio FIFO
writeBuf(RegFifo, LMIC.frame, LMIC.dataLen);
// enable antenna switch for TX
hal_pin_rxtx(1);
// now we actually start the transmission
opmode(OPMODE_TX);
#if LMIC_DEBUG_LEVEL > 0
u1_t sf = getSf(LMIC.rps) + 6; // 1 == SF7
u1_t bw = getBw(LMIC.rps);
u1_t cr = getCr(LMIC.rps);
lmic_printf("%lu: TXMODE, freq=%lu, len=%d, SF=%d, BW=%d, CR=4/%d, IH=%d\n",
os_getTime(), LMIC.freq, LMIC.dataLen, sf,
bw == BW125 ? 125 : (bw == BW250 ? 250 : 500),
cr == CR_4_5 ? 5 : (cr == CR_4_6 ? 6 : (cr == CR_4_7 ? 7 : 8)),
getIh(LMIC.rps)
);
#endif
}
// start transmitter (buf=LMIC.frame, len=LMIC.dataLen)
static void starttx () {
ASSERT( (readReg(RegOpMode) & OPMODE_MASK) == OPMODE_SLEEP );
if(getSf(LMIC.rps) == FSK) { // FSK modem
txfsk();
} else { // LoRa modem
txlora();
}
// the radio will go back to STANDBY mode as soon as the TX is finished
// the corresponding IRQ will inform us about completion.
}
enum { RXMODE_SINGLE, RXMODE_SCAN, RXMODE_RSSI };
static CONST_TABLE(u1_t, rxlorairqmask)[] = {
[RXMODE_SINGLE] = IRQ_LORA_RXDONE_MASK|IRQ_LORA_RXTOUT_MASK,
[RXMODE_SCAN] = IRQ_LORA_RXDONE_MASK,
[RXMODE_RSSI] = 0x00,
};
// start LoRa receiver (time=LMIC.rxtime, timeout=LMIC.rxsyms, result=LMIC.frame[LMIC.dataLen])
static void rxlora (u1_t rxmode) {
// select LoRa modem (from sleep mode)
opmodeLora();
ASSERT((readReg(RegOpMode) & OPMODE_LORA) != 0);
// enter standby mode (warm up))
opmode(OPMODE_STANDBY);
// don't use MAC settings at startup
if(rxmode == RXMODE_RSSI) { // use fixed settings for rssi scan
writeReg(LORARegModemConfig1, RXLORA_RXMODE_RSSI_REG_MODEM_CONFIG1);
writeReg(LORARegModemConfig2, RXLORA_RXMODE_RSSI_REG_MODEM_CONFIG2);
} else { // single or continuous rx mode
// configure LoRa modem (cfg1, cfg2)
configLoraModem();
// configure frequency
configChannel();
}
// set LNA gain
writeReg(RegLna, LNA_RX_GAIN);
// set max payload size
writeReg(LORARegPayloadMaxLength, 64);
#if !defined(DISABLE_INVERT_IQ_ON_RX)
// use inverted I/Q signal (prevent mote-to-mote communication)
writeReg(LORARegInvertIQ, readReg(LORARegInvertIQ)|(1<<6));
#endif
// set symbol timeout (for single rx)
writeReg(LORARegSymbTimeoutLsb, LMIC.rxsyms);
// set sync word
writeReg(LORARegSyncWord, LORA_MAC_PREAMBLE);
// configure DIO mapping DIO0=RxDone DIO1=RxTout DIO2=NOP
writeReg(RegDioMapping1, MAP_DIO0_LORA_RXDONE|MAP_DIO1_LORA_RXTOUT|MAP_DIO2_LORA_NOP);
// clear all radio IRQ flags
writeReg(LORARegIrqFlags, 0xFF);
// enable required radio IRQs
writeReg(LORARegIrqFlagsMask, ~TABLE_GET_U1(rxlorairqmask, rxmode));
// enable antenna switch for RX
hal_pin_rxtx(0);
// now instruct the radio to receive
if (rxmode == RXMODE_SINGLE) { // single rx
hal_waitUntil(LMIC.rxtime); // busy wait until exact rx time
opmode(OPMODE_RX_SINGLE);
} else { // continous rx (scan or rssi)
opmode(OPMODE_RX);
}
#if LMIC_DEBUG_LEVEL > 0
if (rxmode == RXMODE_RSSI) {
lmic_printf("RXMODE_RSSI\n");
} else {
u1_t sf = getSf(LMIC.rps) + 6; // 1 == SF7
u1_t bw = getBw(LMIC.rps);
u1_t cr = getCr(LMIC.rps);
lmic_printf("%lu: %s, freq=%lu, SF=%d, BW=%d, CR=4/%d, IH=%d\n",
os_getTime(),
rxmode == RXMODE_SINGLE ? "RXMODE_SINGLE" : (rxmode == RXMODE_SCAN ? "RXMODE_SCAN" : "UNKNOWN_RX"),
LMIC.freq, sf,
bw == BW125 ? 125 : (bw == BW250 ? 250 : 500),
cr == CR_4_5 ? 5 : (cr == CR_4_6 ? 6 : (cr == CR_4_7 ? 7 : 8)),
getIh(LMIC.rps)
);
}
#endif
}
static void rxfsk (u1_t rxmode) {
// only single rx (no continuous scanning, no noise sampling)
ASSERT( rxmode == RXMODE_SINGLE );
// select FSK modem (from sleep mode)
//writeReg(RegOpMode, 0x00); // (not LoRa)
opmodeFSK();
ASSERT((readReg(RegOpMode) & OPMODE_LORA) == 0);
// enter standby mode (warm up))
opmode(OPMODE_STANDBY);
// configure frequency
configChannel();
// set LNA gain
//writeReg(RegLna, 0x20|0x03); // max gain, boost enable
writeReg(RegLna, LNA_RX_GAIN);
// configure receiver
writeReg(FSKRegRxConfig, 0x1E); // AFC auto, AGC, trigger on preamble?!?
// set receiver bandwidth
writeReg(FSKRegRxBw, 0x0B); // 50kHz SSb
// set AFC bandwidth
writeReg(FSKRegAfcBw, 0x12); // 83.3kHz SSB
// set preamble detection
writeReg(FSKRegPreambleDetect, 0xAA); // enable, 2 bytes, 10 chip errors
// set sync config
writeReg(FSKRegSyncConfig, 0x12); // no auto restart, preamble 0xAA, enable, fill FIFO, 3 bytes sync
// set packet config
writeReg(FSKRegPacketConfig1, 0xD8); // var-length, whitening, crc, no auto-clear, no adr filter
writeReg(FSKRegPacketConfig2, 0x40); // packet mode
// set sync value
writeReg(FSKRegSyncValue1, 0xC1);
writeReg(FSKRegSyncValue2, 0x94);
writeReg(FSKRegSyncValue3, 0xC1);
// set preamble timeout
writeReg(FSKRegRxTimeout2, 0xFF);//(LMIC.rxsyms+1)/2);
// set bitrate
writeReg(FSKRegBitrateMsb, 0x02); // 50kbps
writeReg(FSKRegBitrateLsb, 0x80);
// set frequency deviation
writeReg(FSKRegFdevMsb, 0x01); // +/- 25kHz
writeReg(FSKRegFdevLsb, 0x99);
// configure DIO mapping DIO0=PayloadReady DIO1=NOP DIO2=TimeOut
writeReg(RegDioMapping1, MAP_DIO0_FSK_READY|MAP_DIO1_FSK_NOP|MAP_DIO2_FSK_TIMEOUT);
// enable antenna switch for RX
hal_pin_rxtx(0);
// now instruct the radio to receive
hal_waitUntil(LMIC.rxtime); // busy wait until exact rx time
opmode(OPMODE_RX); // no single rx mode available in FSK
}
static void startrx (u1_t rxmode) {
ASSERT( (readReg(RegOpMode) & OPMODE_MASK) == OPMODE_SLEEP );
if(getSf(LMIC.rps) == FSK) { // FSK modem
rxfsk(rxmode);
} else { // LoRa modem
rxlora(rxmode);
}
// the radio will go back to STANDBY mode as soon as the RX is finished
// or timed out, and the corresponding IRQ will inform us about completion.
}
// get random seed from wideband noise rssi
void radio_init () {
hal_disableIRQs();
// manually reset radio
#ifdef CFG_sx1276_radio
hal_pin_rst(0); // drive RST pin low
#else
hal_pin_rst(1); // drive RST pin high
#endif
hal_waitUntil(os_getTime()+ms2osticks(1)); // wait >100us
hal_pin_rst(2); // configure RST pin floating!
hal_waitUntil(os_getTime()+ms2osticks(5)); // wait 5ms
opmode(OPMODE_SLEEP);
// some sanity checks, e.g., read version number
u1_t v = readReg(RegVersion);
#ifdef CFG_sx1276_radio
ASSERT(v == 0x12 );
#elif CFG_sx1272_radio
ASSERT(v == 0x22);
#else
#error Missing CFG_sx1272_radio/CFG_sx1276_radio
#endif
// seed 15-byte randomness via noise rssi
rxlora(RXMODE_RSSI);
while( (readReg(RegOpMode) & OPMODE_MASK) != OPMODE_RX ); // continuous rx
for(int i=1; i<16; i++) {
for(int j=0; j<8; j++) {
u1_t b; // wait for two non-identical subsequent least-significant bits
while( (b = readReg(LORARegRssiWideband) & 0x01) == (readReg(LORARegRssiWideband) & 0x01) );
randbuf[i] = (randbuf[i] << 1) | b;
}
}
randbuf[0] = 16; // set initial index
#ifdef CFG_sx1276mb1_board
// chain calibration
writeReg(RegPaConfig, 0);
// Launch Rx chain calibration for LF band
writeReg(FSKRegImageCal, (readReg(FSKRegImageCal) & RF_IMAGECAL_IMAGECAL_MASK)|RF_IMAGECAL_IMAGECAL_START);
while((readReg(FSKRegImageCal)&RF_IMAGECAL_IMAGECAL_RUNNING) == RF_IMAGECAL_IMAGECAL_RUNNING){ ; }
// Sets a Frequency in HF band
u4_t frf = 868000000;
writeReg(RegFrfMsb, (u1_t)(frf>>16));
writeReg(RegFrfMid, (u1_t)(frf>> 8));
writeReg(RegFrfLsb, (u1_t)(frf>> 0));
// Launch Rx chain calibration for HF band
writeReg(FSKRegImageCal, (readReg(FSKRegImageCal) & RF_IMAGECAL_IMAGECAL_MASK)|RF_IMAGECAL_IMAGECAL_START);
while((readReg(FSKRegImageCal) & RF_IMAGECAL_IMAGECAL_RUNNING) == RF_IMAGECAL_IMAGECAL_RUNNING) { ; }
#endif /* CFG_sx1276mb1_board */
opmode(OPMODE_SLEEP);
hal_enableIRQs();
}
// return next random byte derived from seed buffer
// (buf[0] holds index of next byte to be returned)
u1_t radio_rand1 () {
u1_t i = randbuf[0];
ASSERT( i != 0 );
if( i==16 ) {
os_aes(AES_ENC, randbuf, 16); // encrypt seed with any key
i = 0;
}
u1_t v = randbuf[i++];
randbuf[0] = i;
return v;
}
u1_t radio_rssi () {
hal_disableIRQs();
u1_t r = readReg(LORARegRssiValue);
hal_enableIRQs();
return r;
}
static CONST_TABLE(u2_t, LORA_RXDONE_FIXUP)[] = {
[FSK] = us2osticks(0), // ( 0 ticks)
[SF7] = us2osticks(0), // ( 0 ticks)
[SF8] = us2osticks(1648), // ( 54 ticks)
[SF9] = us2osticks(3265), // ( 107 ticks)
[SF10] = us2osticks(7049), // ( 231 ticks)
[SF11] = us2osticks(13641), // ( 447 ticks)
[SF12] = us2osticks(31189), // (1022 ticks)
};
// called by hal ext IRQ handler
// (radio goes to stanby mode after tx/rx operations)
void radio_irq_handler (u1_t dio) {
ostime_t now = os_getTime();
if( (readReg(RegOpMode) & OPMODE_LORA) != 0) { // LORA modem
u1_t flags = readReg(LORARegIrqFlags);
#if LMIC_DEBUG_LEVEL > 1
lmic_printf("%lu: irq: dio: 0x%x flags: 0x%x\n", now, dio, flags);
#endif
if( flags & IRQ_LORA_TXDONE_MASK ) {
// save exact tx time
LMIC.txend = now - us2osticks(43); // TXDONE FIXUP
} else if( flags & IRQ_LORA_RXDONE_MASK ) {
// save exact rx time
if(getBw(LMIC.rps) == BW125) {
now -= TABLE_GET_U2(LORA_RXDONE_FIXUP, getSf(LMIC.rps));
}
LMIC.rxtime = now;
// read the PDU and inform the MAC that we received something
LMIC.dataLen = (readReg(LORARegModemConfig1) & SX1272_MC1_IMPLICIT_HEADER_MODE_ON) ?
readReg(LORARegPayloadLength) : readReg(LORARegRxNbBytes);
// set FIFO read address pointer
writeReg(LORARegFifoAddrPtr, readReg(LORARegFifoRxCurrentAddr));
// now read the FIFO
readBuf(RegFifo, LMIC.frame, LMIC.dataLen);
// read rx quality parameters
LMIC.snr = readReg(LORARegPktSnrValue); // SNR [dB] * 4
LMIC.rssi = readReg(LORARegPktRssiValue) - 125 + 64; // RSSI [dBm] (-196...+63)
} else if( flags & IRQ_LORA_RXTOUT_MASK ) {
// indicate timeout
LMIC.dataLen = 0;
}
// mask all radio IRQs
writeReg(LORARegIrqFlagsMask, 0xFF);
// clear radio IRQ flags
writeReg(LORARegIrqFlags, 0xFF);
} else { // FSK modem
u1_t flags1 = readReg(FSKRegIrqFlags1);
u1_t flags2 = readReg(FSKRegIrqFlags2);
if( flags2 & IRQ_FSK2_PACKETSENT_MASK ) {
// save exact tx time
LMIC.txend = now;
} else if( flags2 & IRQ_FSK2_PAYLOADREADY_MASK ) {
// save exact rx time
LMIC.rxtime = now;
// read the PDU and inform the MAC that we received something
LMIC.dataLen = readReg(FSKRegPayloadLength);
// now read the FIFO
readBuf(RegFifo, LMIC.frame, LMIC.dataLen);
// read rx quality parameters
LMIC.snr = 0; // determine snr
LMIC.rssi = 0; // determine rssi
} else if( flags1 & IRQ_FSK1_TIMEOUT_MASK ) {
// indicate timeout
LMIC.dataLen = 0;
} else {
ASSERT(0);
}
}
// go from stanby to sleep
opmode(OPMODE_SLEEP);
// run os job (use preset func ptr)
os_setCallback(&LMIC.osjob, LMIC.osjob.func);
}
void os_radio (u1_t mode) {
hal_disableIRQs();
switch (mode) {
case RADIO_RST:
// put radio to sleep
opmode(OPMODE_SLEEP);
break;
case RADIO_TX:
// transmit frame now
starttx(); // buf=LMIC.frame, len=LMIC.dataLen
break;
case RADIO_RX:
// receive frame now (exactly at rxtime)
startrx(RXMODE_SINGLE); // buf=LMIC.frame, time=LMIC.rxtime, timeout=LMIC.rxsyms
break;
case RADIO_RXON:
// start scanning for beacon now
startrx(RXMODE_SCAN); // buf=LMIC.frame
break;
}
hal_enableIRQs();
}
The entire file, really?
And text posted as text isn’t an option, it’s helping with the forum search, which you could try …
As well as reviewing the README relating to radio cfg as implied by the lines around 689 …
You could just paste the few lines concerned in stead of the entire file…
Can you use search? This isn’t the first time a question has been asked about this error. The last time was less than a week ago… also googling what an assert is used for might enlighten you what is wrong.
Hint, controller seems not get the right result from the rfm module. Are you pin mappings correct??
Sorry I thought you asked for the whole file.
I’m a debutant here.It’s my firts time on forums.
Yes I saw that some were talking about pin mapping problem. But how to check the pin mapping?
Sorry if my questions seem obvious to you, I just don’t understand.
And thank you in advance for your understanding.